Floorball Blades

When choosing a blade, three main aspects should be considered: concavity, pre-curve, and material.

Concavity: The deeper the concavity of the blade, the better the ball stays on the blade during shots and dekes. A deep concavity (e.g., 9.5 mm) is suitable for goal scorers. A moderate concavity (e.g., 8.0 mm), on the other hand, makes backhand play and accurate passes easier.

Pre-curve: A pre-curved blade helps to get the ball up more easily and provides extra power for wrist shots. Straighter blades are favored by playmakers due to their predictability.

Stiffness and Weight: Manufacturers use different plastic compounds that have a significant effect on stickhandling feel. Lightweight blades make the stick tip-light and quick to handle. Stiffer, carbon-fiber reinforced blades, on the other hand, offer maximum power transfer for hard shots.

Manufacturers use various plastic compounds, which greatly affect the feel of the ball.

OXDOG BLADE MATERIALS

MB (Medium Blade)
Medium-stiff material, good durability, and general feel with soft ball touch.

NB (Normal Blade)
Slightly softer than MB material, the blade surface is harder than MB material. A very slick material on all playing surfaces.

MBC/NBC (Medium/Normal Blade Carbon)
The blade contains a carbon fiber reinforcement, which makes the blade stiffer without significant added weight. The number of carbon fiber pieces/plates varies from one to three, depending on the blade model.

CPB (Carbon Polymer Blade)
Premium material combining carbon fiber and lightweight polymer – for maximum stiffness and lightness.

FAT PIPE BLADE MATERIALS

PP SOFT (PPS)
Durable and soft polypropylene material that offers a silky soft ball touch.

PP BOOST (PPB)
Durable and medium-stiff polypropylene material with a soft ball touch.

PP HARD (PPH)
Durable and stiff material. 20% stiffer and slicker than PP Boost, while maintaining the good ball touch of polypropylene blades.

PE
Polyethylene is a durable and medium-stiff material with a good ball touch. Polyethylene slides best on every surface. The surface of a PE blade feels harder than the surface of a polypropylene blade.

Hybrids (e.g., SLICKS)
The latest innovations combine the best qualities of both materials: a soft feel for the ball and a slick base against the floor.

The blade is a wearing part of the stick. It should be replaced with a new one when:

The blade has loosened: Continuous shooting fatigues the plastic, causing the blade to give way and shots no longer feel crisp.

The base is worn: When the blade's base has worn thin and sharp, the blade should be replaced with a new one. This is also for safer play.

You want to change your playing style: Sometimes, simply changing the blade from a straighter one to a more curved one (or vice versa) can change your playing and give your stick a whole new life without needing to replace the entire stick.

The blade of a floorball stick is a wearing part, but changing it is quite simple.

Removing the screws: Unscrew the fastening screws in the heel of the blade. Keep them safe unless you are replacing them with new ones.

Heating: Gently heat the heel of the blade with a heat gun. The heat will cause the plastic to expand and any glue to soften, making the blade easier to remove. Be careful not to burn the shaft or the blade!

Removal: Pull the old blade off the shaft with a firm motion. If the blade is stuck, try gently wiggling it while pulling.

Installing a new blade: Heat the heel of the new blade for a moment so that it slides into place more easily. Push the blade onto the end of the shaft as far as it goes. Pay attention to the grooves on the bottom of the blade, which lock the blade at the correct angle. Make sure the blade is straight in relation to the shaft's shape.

Fastening: Screw the screws back into place. If the new blade is a different model than the old one, you may need to drill new small pilot holes into the stick's shaft. New holes in the shaft will not weaken the shaft in any way.

Tip: Always check after changing that the blade does not move. A firmly attached blade guarantees the best ball control and safety on the field. If blades have been changed on the shaft many times, it is advisable to use blade glue during installation to ensure the blade stays firmly in place and does not move. (Old screw holes always enlarge over time, and after this, the glue will hold the blade firmly in place).

Remember that in official matches, the stick and blade must bear the stamp of the same manufacturer. Therefore, the blade and shaft must be assembled using components from the same manufacturer.